The Lone 60/40 Best Double Kitchen Sink Measures Closer to 58/42

1. KRAUS Premier 32-Inch Undermount 50/50 Double Bowl Low Divider Sink, 18-Gauge, KBU32 — Best Overall

The most completely measured stainless sink on the page, with the only undermount-only fitting and a lifetime warranty in writing.

Key Specifications

Why We Recommend It

This is the stainless listing that measures what you will actually use. The second bullet gives the outside, “32 1/4 in. L x 18 7/8 in. W x 9 in. D”, then the inside: “BOWL DIMS (Both Bowls): 14 1/2 in. L x 16 7/8 in. W x 8 5/8 in.” It names the cabinet, “MIN. CABINET SIZE: 36””, and lists the kit. No other stainless sink here gives you bowl length, bowl width, bowl depth, cabinet and contents in one place.

The split is even, and the divider is low. The title says “50/50 Double Bowl Low Divider” and the fifth bullet says what that is for: “extra clearance for washing large items across both bowls without overflow”. It does not give the divider’s height, so you cannot tell from the page how far below the rim it stops. Each bowl’s floor works out at about 245 square inches, by our arithmetic, and as a rough box each holds about 9.1 US gallons. That is more floor per bowl than the 33-inch Quarza, though the KBU32 is three quarters of an inch shorter overall, because thin steel walls give up less room than composite.

18-gauge is the middle of the stated range. The listing says “HEAVY-DUTY 18-GAUGE stainless steel sinks resist dents and damage”. By the standard sheet gauge, 18-gauge is about 1.2mm, our conversion, against about 1.6mm for the 16-gauge Delironexu and LQS and about 0.95mm for the ATTOP’s 20-gauge bowl. The listed weight, 18.43 pounds, is the only stainless weight here that comes with a stated gauge. The fourth bullet adds “large silencer pads on all sides” and a “gently sloped bottom to keep water from pooling”.

It is the only undermount-only sink on the page, and that sets the counter. An undermount sink hangs below a solid countertop such as stone or quartz; it cannot go into laminate, which needs a drop-in rim to cover the cut edge. Seven of the ten here are drop-in only, and the two KRAUS granite sinks can go either way. If you are replacing a drop-in sink in a laminate counter, this is not your sink. Our undermount kitchen sink roundup covers the fitting in detail.

The drains are centre-set. The kit lists “Kitchen sink with center-set drains, drain assembly with strainer (x2)”, and KRAUS recommends a disposal, “KWD100-75MBL (sold separately)”. A centre drain puts the outlet, and any disposal hanging from it, in the middle of the space under each bowl, where a rear drain would leave more room for storage behind the doors. Faucet holes are not stated; with an undermount sink the faucet normally goes through the countertop, so the counter fabricator drills them.

What to weigh. It is sold by Amazon.com and ranks #34,338 overall and #7 in Double Bowl. Its two fields disagree on height, 9 inches in the bullet and 8.5 in the spec table, and on width, 18 7/8 inches against 19.0; plan for the larger figures. It is one of only two listings here to state a warranty, “Limited Lifetime Warranty”. Against the field, it is the stainless sink with the fewest unknowns.

Best for: A stone or quartz countertop, a 36 in cabinet, and a buyer who wants every bowl dimension and a warranty in writing.

View on Amazon

2. KRAUS 33-Inch White Granite Double Bowl Kitchen Sink, 60/40, KGD-50WHITE — Best 60/40 Split

The only sink here sold as 60/40, and the only one that measures a big bowl and a small bowl separately.

Key Specifications

Why We Recommend It

This is the one listing on the page that answers the 60/40 question. The second bullet says “DOUBLE BOWL SINK with 60/40 split and rear-set drains”, and the first gives both bowls: “Large bowl: 15 1/4 in L x 18 1/2 in W x 8 7/8 in D; Small bowl: 12 7/8 in L x 16 in W x 8 7/8 in H”. If you came looking for the best 60/40 kitchen sink, this is the only one of ten that says it is one.

Its own numbers put it nearer 58/42. The large bowl’s floor is about 282 square inches and the small bowl’s about 206, by our arithmetic, so the large bowl takes about 58% of the floor. By length alone it is about 54/46. Neither is wrong; 60/40 is the trade name for an unequal double sink, and the bowl sizes are what you should compare. The two bowls together, about 488 square inches, have almost exactly the floor of the KBU32’s two equal bowls. The space is the same; the KGD-50WHITE puts more of it on one side.

The large bowl is the deepest front to back on the page. At 18 1/2 inches from front to back, it is the only bowl here longer in that direction than a standard 18 by 13 inch half sheet pan, so on paper a sheet pan can lie flat in it. Rounded corners and a sloped floor will take some of that margin. Each bowl is 8 7/8 inches deep, and as a rough box the large bowl holds about 10.8 US gallons and the small about 7.9, our arithmetic. That is the case for an unequal split: one bowl big enough to soak a roasting tin, one small enough to rinse in while the other is full.

Composite changes the care. KRAUS calls it granite and explains it as “advanced quartz composite material w/ the look of natural granite”, “naturally sound-absorbing” and “COLOR-STABLE”. It also warns: “although the Forteza sink is heat resistant, extremely hot items may cause discoloration”. That is why the kit includes a silicone mitt and trivet, the only sink here to pack either. At 39.2 pounds listed, it is more than twice the KBU32’s weight, which matters for an undermount fit, where the clips and adhesive carry the sink and whatever is in it.

It fits either way. The listing says it “installs as a drop in sink with any countertop or as an undermount sink”, with templates for both. That makes it one of only two sinks here, both KRAUS composite, that suit a laminate drop-in replacement and a new stone counter alike. The drains are rear-set, which leaves more open floor in each bowl and more room under the sink, and KRAUS recommends “GARBAGE DISPOSAL KWD211-75MCG (sold separately)”.

What to weigh. It is sold by Amazon.com and was flagged as scarce stock at capture. It ranks #40,471 overall, and Amazon files it at #53 in Single Bowl, an odd category for a two-bowl sink. No warranty is stated. Faucet holes are not stated either, which matters more here than on the undermount KBU32: dropped in, it needs either holes in the deck or a faucet mounted through the counter behind it, so ask before you order.

Best for: A buyer who wants one big soaking bowl and one rinse bowl, in either a drop-in or undermount fit.

View on Amazon

3. Delironexu 33 x 19 Drop-In Double Bowl Kitchen Sink, 16-Gauge 304 Stainless, DETD3319 — Best Drop-In

The thickest stated steel on the page, two measured bowls, and a cutout size you can check against the hole you already have.

Key Specifications

Why We Recommend It

This listing reads like a replacement-sink spec sheet. The third bullet gives the outside, “33” L x 19” W x 9” D”, the inside, “50/50 double bowl interior dimensions of 15” L x 15” W x 8.95” D each”, and the hole in the counter, “a cutout size of 32” L x 18” W”. Only three listings here give a cutout at all, and this is the only one that also measures both bowls.

16-gauge is the thickest gauge stated on the page. The first bullet says “handmade from premium 16-gauge 304 stainless steel”. Only the LQS matches it. By standard sheet gauge, 16 is about 1.6mm, against about 1.2mm for the 18-gauge KBU32 and about 0.95mm for the ATTOP’s 20-gauge bowl, our conversions. Lower gauge numbers mean thicker steel, which resists denting and drums less when a pot lands. The listing does not give a weight, so there is no second figure to cross-check the gauge against.

33 by 19 is a replacement size. The Elkay Dayton has the same 33 by 19 inch outline, and the listing names the market it is aiming at: “residential kitchens, mobile home kitchen sink, and manufactured home kitchen sink applications”, and “sink replacements, kitchen updates, and countertop upgrades”. If your old sink is a 33 by 19 drop-in, the stated 32 by 18 inch cutout is the figure to measure against before anything else. The bowls are square, 15 by 15 inches, about 225 square inches of floor each and about 8.7 US gallons as a rough box, our arithmetic.

Both drains are accounted for. “The standard 3.5” drain openings fit most kitchen sink drains and garbage disposals”, and the box holds “two drain assemblies”. That matters on a double sink, where each bowl needs its own drain and the two usually join under the sink before the trap. Drain position is not stated. The bullets add “X-shaped grooves”, “R10 tight-radius corners” and sound pads “covering over 80% of the bottom and sides”.

What to weigh. It is sold by DESUNLUNG and ranks #76,384 overall and #5 in Double Bowl. The listing gives no minimum cabinet, no warranty and no faucet-hole count. The model field reads DETD3319 and the part number 063. For a drop-in counter, it states more of what you need to check than any other stainless listing here, and the thickest steel to go with it.

Best for: A drop-in replacement in a 33 x 19 opening, by a buyer who wants the thickest stated steel.

View on Amazon

4. ATTOP 33-Inch Large Double Bowl Drop-In Kitchen Sink, 33 x 22 x 9 — Best Seller

The best-ranked double sink on the page, with a stated gauge and cutout, and no split or bowl sizes.

Key Specifications

Why We Recommend It

This is the double sink Amazon sells most of among these ten, and it does not say how it splits. It ranks #14,095 overall and #1 in Double Bowl, well ahead of every other sink here. The title says “Large Double Bowls”. The bullets give the outside, “33” L x 22” W (front-to-back) x 9””, and nowhere give a bowl size, a ratio or a divider height.

It does give two thicknesses. The first bullet reads “3.0mm edge plate and 20 Gauge bowl stainless steel thickness”. The edge plate is the flat rim that sits on the counter; the bowl is the part that takes the pots. By standard sheet gauge, 20-gauge is about 0.95mm, our conversion, the thinnest gauge stated on the page, under the 18-gauge KBU32 and the 16-gauge Delironexu and LQS. The thicker rim helps a drop-in sink sit flat; it does not make the bowl stiffer. The listing pairs it with “Heavy duty sound guard undercoating and thick rubber padding”.

The fitting figures are the useful part. The spec table gives the “Countertop cutout size :32”x21””, one of only three cutouts on the page, and the drain: “USA standard 3.5” drain opening will fit any garbage disposal unit”, with “Rear drain placement” that, the listing says, “ensures dishes don’t settle on the drain”. At 22 inches front to back, it needs a counter deep enough for that outline plus a faucet behind it. No minimum cabinet is stated; a 33-inch-wide sink normally means a 36-inch base cabinet.

The accessories are a grid and a strainer. “Stainless steel bottom rinse grid can protect the sink from scratches and acts as a drying rack”, and there is a “Stainless steel basket strainer drain”. The listing uses the singular for both, so check whether you get one grid and one strainer or a pair; a double sink needs a strainer in each drain. The finish is described as “Nano coating” over brushed steel.

What to weigh. It is sold by ATTOP KITCHEN EQUIPMENT. There is no warranty statement, no listed weight and no model number beyond a description, “Silver 33”X22”X9” double bowls”, and the spec table’s item count reads 30 for what is one sink. The rank says it sells; the listing leaves you to work out the bowls. Ask the seller for both bowl sizes and the divider height before you buy it for a particular pan.

Best for: A drop-in replacement in a 32 x 21 in cutout, where the buyer can confirm bowl sizes with the seller.

View on Amazon

5. KRAUS Quarza 33-Inch Granite Drop-In/Undermount 50/50 Double Bowl Sink, White, KGD-433BWHITE — Deepest Bowls

Two equal bowls at 9 1/2 inches deep, the deepest on the page, in a composite that drops in or mounts under.

Key Specifications

Why We Recommend It

The Quarza trades footprint for depth. The first bullet gives “Dims: 33 in L x 22 in W x 10 1/8 in D; Bowl dims (both bowls): 14 1/4 in L x 15 1/2 in W x 9 1/2 in D”. At 9 1/2 inches, each bowl is the deepest on the page. At 14 1/4 by 15 1/2 inches, each bowl is also the smallest of any 33-inch sink that states bowl sizes.

On our arithmetic the two effects cancel. Each bowl’s floor is about 221 square inches, against about 245 on the 32 1/4-inch KBU32. As rough boxes, each Quarza bowl holds about 9.1 US gallons and each KBU32 bowl about 9.1 as well. The Quarza gets its volume by going down; the KBU32 by going out. Depth keeps splashes in and lets a tall stockpot stand upright; floor area is what lets a wide pan lie flat. A 15 1/2-inch front-to-back bowl will not take an 18-inch sheet pan flat; the KGD-50WHITE’s 18 1/2-inch large bowl will.

The composite walls take the room. This sink and the KGD-50WHITE share a 33 by 22 inch outline, and the Quarza’s two bowls together have about 442 square inches of floor against the KGD-50WHITE’s 488, by our arithmetic. Composite is thicker than sheet steel at the walls, the rim and the divider. KRAUS describes the material in the same terms as the KGD-50WHITE, “advanced quartz composite material w/ the look of natural granite”, and carries the same warning: “although the Quarza sink is heat resistant, extremely hot items may cause discoloration”. There is no mitt or trivet in this kit.

The 10 1/8-inch overall height is the cabinet figure to check. Undermounted, that much sink hangs below the counter, and it is the tallest outline on the page. Drains and any disposal hang below that again. KRAUS recommends the same disposal as for the KGD-50WHITE, “KWD211-75MCG (sold separately)”, and the drains are rear-set, which helps keep the space under the sink usable. At 40.7 pounds listed, it is second only to the Karran’s 46.0.

What to weigh. It is sold by Amazon.com, was flagged as scarce stock at capture, and ranks #56,776 overall and #9 in Double Bowl. It fits as a drop-in or undermount and needs a 36-inch cabinet. No warranty and no faucet-hole count are stated. For deep, equal bowls in composite, it is the clearest listing here; for a sheet pan, it is the wrong shape.

Best for: Tall stockpots and splash control in a composite sink, in a 36 in cabinet with room below.

View on Amazon

6. Elkay Dayton D233191 Equal Double Bowl Drop-In Stainless Steel Sink, 33 x 19 x 6-7/16 — Best for Accessibility

The shallowest sink on the page by design: 6 7/16 inches deep and stated ADA compliant, with a lifetime warranty.

Key Specifications

Why We Recommend It

Every other sink here is 8 to 10 inches deep; this one is built to be shallow. The title gives “33 x 19 x 6.4375”, the bullet “33” X 19” X 6-7/16””, and the second bullet explains why: “ADA COMPLIANT: Product is ADA compliant when properly installed.” US accessibility guidance limits sink bowl depth to 6 1/2 inches so a seated user can reach the bottom and knees fit beneath, which explains the 6 7/16.

That depth is the whole trade. Its overall depth is 2 3/16 inches less than the KBU32’s bowl depth and 3 1/16 inches less than the Quarza’s, by our arithmetic. A shallow bowl is easier to reach into and kinder to backs, and it gives a wheelchair user a sink they can use. It also splashes more and holds less. If nobody in your house needs the reach, a deeper sink will contain a running tap better.

The split is equal and the bowls are not measured. “DOUBLE BOWLS OF EQUAL SIZE: Conveniently use bowls independently for washing, soaking, rinsing, drying and other household tasks.” The listing gives no bowl length or width, so you know the bowls match and not how big they are. The outline is 33 by 19 inches, the same as the Delironexu, and the minimum cabinet is stated: “Min. Cabinet Size: 36””.

The steel is named by series, not gauge. “300 SERIES STAINLESS STEEL: Designed for everyday use.” 300 series is the family that includes 304, which four other listings name. The gauge is not given. The listed weight is 10.0 pounds, the lightest stated weight on the page, and with a shallower bowl there is less steel to weigh. Elkay adds “Sound-deadening pad(s)” and a “U-CHANNEL INSTALLATION” with clips placed in the channel beforehand, “less time under the sink for an easier install”.

What to weigh. It is sold by Amazon.com, was flagged as scarce stock at capture, and ranks #57,978 overall and #2 in Double Bowl. The drain size is stated, “Drain Size- 3-1/2 inch”, but no strainers are listed. It is one of two sinks here with a stated warranty, “Limited Lifetime”. Model D233191 is a real part number you can quote to a plumber or a supplier.

Best for: An accessible kitchen, or any cook who wants a sink they can reach the bottom of without bending.

View on Amazon

7. LQS 33 x 22 Black Drop-In 50/50 Double Bowl Sink with Low Divider, 16-Gauge 304 Stainless — Best Low Divider

One of two listings that give the divider a number, with 16-gauge steel and the fullest box of extras on the page.

Key Specifications

Why We Recommend It

This is one of two dividers on the page with a figure attached, and the only one in stainless. The first bullet says “Ultra low divide design, smart divider is in the middle of the kitchen sink. 4-1/2” depth divider can make the sink used in two different ways.” It does not say whether 4 1/2 inches is measured from the rim down or from the floor up. In a sink stated as 9 inches deep, by our arithmetic, it is half way either way, so the answer is the same: the divider stops at mid-depth.

A half-height divider makes two sinks in one. Fill below the divider and the bowls work apart; fill above it, or lay a long pan across, and the listing says the sink “can also be used as a single bowl kitchen sink”, “Giving you extra clearance to wash large items”. The interior is given as one figure, “Interior dimension: 30” L x 17” W x 9” D”, so a baking tray up to about 30 inches long fits across both bowls above the divider, on paper. A 17-inch front-to-back interior will not take an 18-inch sheet pan flat in one bowl.

16-gauge, coated black. “crafted from heavy-duty 16-gauge 304 stainless steel”, the same gauge as the Delironexu and the thickest stated here, about 1.6mm by standard gauge, our conversion. The colour is a “gunmetal black finish” applied with “advanced Nano PVD coating”. The listing promises resistance to stains, corrosion and scratches “(yes, even from pots and knives!)”; a coating is still a layer over the steel, and the listing gives no warranty to stand behind that promise.

It doubles as a workstation sink. “Front and back ledges provide extra workspace”, and the package list includes “two black sink protector grids, two black sink drain strainers, a black rolling-up rack, a black colander”. One conflict: the sixth bullet says a “cutting board can slide smoothly along the tracks”, and the package list does not include one. Ask before you count on it. Our workstation kitchen sink guide covers ledge sinks in more depth.

What to weigh. It is sold by LQS Electronic factory and ranks #94,543 overall and #13 in Double Bowl. The cabinet is stated, “Cabinet size is 36””, and the drain, “American standard 3.5” drain opening size fits most garbage disposal unit”. No warranty and no faucet-hole count. For a low divider you can measure in a stainless sink, it is the only listing that tells you; the Karran gives a figure in composite.

Best for: A buyer who wants a true low divider and workstation extras in a 33 x 22 drop-in.

View on Amazon

8. Kitsitchen 33 x 22 Drop-In Kitchen Sink, T304 Stainless Steel Double Bowl, KY-2024-001 — Heaviest Stainless

The heaviest stainless sink by listed weight, with a depth its own fields cannot agree on and no split stated.

Key Specifications

Why We Recommend It

This listing has the most bullets on the page and the fewest bowl figures. Nine bullets describe the material, the layout, the cleaning, the noise and the install. The dimensions come in one line: “(L)33” x (W)22” x (D)8””. There is no bowl size and no split, only “a smart dual-bowl layout”.

The depth fields disagree. The bullet says 8 inches deep; the spec table says 9.0 inches high. One may be the bowl and the other the overall height, but the listing does not say which. A full inch matters on a sink: it is the difference between this being among the shallower stainless sinks here and matching the ATTOP and LQS. Ask the seller for the bowl depth before you rely on either.

The weight is the one figure that stands out. The spec table lists 23.39986448868 pounds, about 23.4, the heaviest stainless sink on the page by listed weight, ahead of the KBU32 at 18.43 and the Elkay at 10.0. No gauge is stated, so weight is the only clue to the steel, and it is a weak one: a 33 by 22 sink has more steel in it than a 32 by 19 one at any gauge, and a listing weight may include packaging. Read it as a hint, not a gauge.

The fitting details are general. “Installs On Granite, Quartz, Laminate And All Countertop Types”, with “a cutting template ,install tips and install clips”. The drains are covered: “accessories including two basket strainers, standard 3.5” drain openings will fit any garbage disposal unit in the US”. No cutout size, no minimum cabinet and no drain position are given. The listing adds a “Vibration-Absorbing Pad And Condensation-Proof Coating” and a “Bottom Slope And X-Shaped Diversion Waterlines Design”.

What to weigh. It is sold by ZHUHAIYIDECHUWEIYOUXIANGONGSI, was flagged as scarce stock at capture, and ranks #78,240 overall and #6 in Double Bowl. The model field reads KY-2024-001, and the part number field reads “Countertop”, which is not a part number. No warranty is stated. It may be a solid sink; the listing leaves the bowls, the split and the depth to the seller.

Best for: A 33 x 22 drop-in replacement, once the seller has confirmed the bowl sizes and depth.

View on Amazon

9. Karran 33-Inch White Granite Composite Drop-In Double Bowl Kitchen Sink, QT-810 — Best Faucet-Ready Composite

The only listing on the page that counts its faucet holes, with a 6-inch low divider and the only stated heat figure.

Key Specifications

Why We Recommend It

This is the one listing of ten that tells you how a faucet goes on. The third bullet says the sink “Includes one pre-drilled faucet hole with additional knockout options for accessories such as soap dispensers or sprayers”. Every other listing on the page is silent on holes. For a drop-in sink, where the faucet usually mounts through the sink deck, that is the fitting fact that decides which faucets will work, and only the Karran gives it.

Its low divider has a figure. The second bullet reads “33-Inch Double Bowl With 6-Inch Low Divider: Features dual 9-inch-deep bowls with a 6-inch low divide”, and says it lets “large pots and baking sheets to move easily across both sides”. Only it and the LQS give a divider number. The listing does not say whether 6 inches is the divider’s height from the floor or its drop from the rim. Read as a height in 9-inch bowls, it stops 3 inches below the rim; read as a drop, 3 inches above the floor, by our arithmetic. Ask which before you count on sliding a sheet pan across.

The split and the bowl sizes are missing. “Dual 9-inch-deep bowls” gives the depth and not the length or width of either bowl, and the listing never says 50/50 or 60/40. The outer size, 33 by 22 by 9 inches, matches both KRAUS composites, so this is the third white composite on the page in the same outline, and the only one of the three without measured bowls.

The composite claims come with a number. “Crafted from 80% natural quartz”, it “resists heat up to 535°F as well as impact, chipping, and thermal shock”. The two KRAUS composites call themselves heat resistant and warn that very hot items may discolour them; the Karran gives a figure instead. At 46.0 pounds listed, it is the heaviest sink on the page. It suits “laminate, granite, quartz, and solid-surface countertops” as a top mount only.

What to weigh. It is sold by KARRAN and ranks #122,593 overall and #17 in Double Bowl, the lowest overall rank on the page. The model field reads QT-810. The first bullet ends “(Strainers sold separetly)”, so you will need two strainers before the sink can drain; the listing gives no drain size or position. No minimum cabinet and no warranty are stated. If the faucet is the first thing you have to get right, this is the only listing that helps.

Best for: A drop-in buyer who needs a sink drilled for one faucet with room for a sprayer or soap dispenser.

View on Amazon

10. Vivrhintty 30-Inch Double Bowl Drop-In/Top-Mount 304 Stainless Steel Sink, 30.7 x 16.9 — Best Budget

The lowest-priced and most compact sink here, with a cutout range and no split, bowl sizes or gauge.

Key Specifications

Why We Recommend It

The lowest-priced sink on the page gives you the counter and not the bowls. The first bullet is about the hole: “Countertop dimensions for this sink are 29.5” x 15.7–16.1”. Please verify your countertop measurements before purchase.” The spec table gives the outside, “30.7×16.9×8.7 in”. Nothing gives a bowl size, a split or a divider height.

The cutout is a range, which is unusual and useful. 15.7 to 16.1 inches front to back is a tolerance: the rim will cover a cut anywhere in that band. If you are replacing a compact sink, that is the figure to measure. No minimum cabinet is stated; a 29.5-inch cutout needs a base cabinet whose inside is wider than that, so check yours. At 30.7 by 16.9 inches it is the smallest outline on the page, and the only double sink here that may suit a base cabinet narrower than 36 inches.

It is the only compact outline here. Every other sink on the page is 32 1/4 or 33 inches long; this one is 30.7 by 16.9 inches. The listing describes 304 stainless with a nano coating, a “3mm thick rubber layer” against noise, an “anti-condensation spray” and a “Smart X-Drainage System” with an x-shaped bottom, and says it suits “kitchens, bars, restaurants, cafeterias, and more”. The manufacturer field reads YISHEN INC and the model field only “001”, which is no help when you need a template or a spare.

The drain is covered. “It comes with a standard 3.5-inch drain outlet—if you don’t need the original drain, you can replace it with a garbage disposal unit.” The kit has “a telescopic basket and under-drain strainer kit”. The listing uses the singular for the drain outlet; a double sink has two, so confirm you get two strainers.

What to weigh. It is sold by Vivrhintty and ranks #60,389 overall and #3 in Double Bowl. No gauge, weight or warranty is stated; the final bullet offers “Customer-First Support” and asks you to contact the seller before a return. For a compact budget replacement where the cutout range fits, it is the simplest listing here; if you need bowl sizes, ask the seller first.

Best for: A compact drop-in replacement where the old cutout falls inside 29.5 x 15.7–16.1 in.

View on Amazon